A pair in size 9.5/10.5 weighs just 1.4 kg.

Lightweight

Prevents the growth of wild vegetation

Cushioning

Designed for hunting and all outdoor activities.

Condition

Reinforced Rubber Boots

Frequency

Lining Material

Boots Type

Season

Weather Conditions

Boot Height

Place of Practice

Main Material

Fastener Type

The Glenarm 100 boots are the lightest in our range. They are barely 1.4kg in size 9/9.5. Whether you’re hunting or out for a stroll, this waterproof boot keeps moisture out, even in muddy, rainy conditions. Made with tear- and abrasion-resistant materials, it’s also Resistant to tears and abrasion.

Lightweight and rugged

To keep your boots in good condition, clean them after each use with water and/or pH-neutral soap (avoid using hard brushes or abrasive sponges). Wipe dry with a cloth or let dry in a well-ventilated place away from heat sources. Store the boots upright, preferably in a dry place with good ventilation. They are fully waterproof and safe to wear in water up to the top of the shaft.

A few care instructions for these PVC boots

3.5/4: 1.0 kg
5/6: 1.1 kg
7/7.5: 1.2 kg
8/9: 1.3 kg 
9.5/10.5: 1.4 kg
11.5/12: 1.5 kg
13/13.5: 1.6 kg

Calf circumference in 8/9: 41 41 cm

Weight (kg)

Size          Calf circumference
2.5/3                        34 cm
4/5                       35 cm
5.5./6.5                        36.5 cm
7/8                        38 cm
8.5/9.5                       39 cm
10/11                       41 cm
12/12.5                       42.5 cm

Calf size

Size                       Inner height (mm)	
12/12.5 	                                     365	
10/11	                                     360	
8.5/9.5	                                      355	
7/8	                                     335	
5.5/6.5	                                     325	
4/5	                                     315	
2.5/3	                                     305

Inner height (mm)	

Boots & Socks

Tested in 2 hours of moderate rain
16,000 mm Schmerber
Non-waterproof pockets

Waterproof

Breathability

Pockets

Adjustable ankle cuffs can fit right over your boots.

Easy dressing

The flat elastic waistband ensures a secure, comfortable fit.

Anatomic design

The pants easily pack down into a pocket.

Compact design

These waterproof pants were developed for inshore sailing in stormy weather.

Maximum wash temperature of 30°C. Very delicate cycle.

Maximum wash temperature 70°C. Normal cycle.

Ironing at a maximum iron soleplate temperature of 200°C.

reinforced area

Number of Pockets

belt height

Precipitation

modular

Windproof

Pocket

Type of Length

Type of Bell

Water-Repellent

Schmerber

We measure the water resistance of a fabric in mm (based on the ISO 811 standard). The higher the water pressure a fabric can withstand, the more waterproof it is.
Waterproofing ratings:
Resistant to water pressure of 2,000 mm before and after ageing (5 washes). That’s equal to 15,000 Schmerber (the average pressure exerted during rainfall).
These pants were tested in 2 hours of moderate rain (60 L/m²/h).

Waterproof properties

Rinse with clean water after use.
Store in a dry place.
Wash as infrequently as possible to protect the water-repellent treatment.
Wash inside out, pocket zipped, on the synthetics cycle (30°C–40°C) with regular detergent. Do not use fabric softener. Do not overload your machine. Run extra rinse.
Line dry.
To restore its water repellency, tumble dry inside out on the synthetics cycle for 10–15 min.

Care instructions

Breathability
To find out if a fabric is breathable, we measure its resistance to evaporative heat transfer (RET). The lower the resistance, the more a fabric allows the body’s perspiration escape.
- RET < 9 = extremely breathable
- RET 9–12 = very breathable
- RET 12–20 = breathable
- RET > 20 = not very or not at all breathable

Clothing

Very light at just barely 1.46 kg in size 43/44.

Lining-free technology: wash inside and out, quick drying.

Easy to care for

Easy-to-put-on mid-calf design with pull loops and grooves.

Ease of use

Traction

Designed for all types of outdoor activities in wet weather.

Jacket Type

These boots are waterproof, very light and soft. dirt is easy to clean off.

Practical and versatile

The PVC boots we offer on this page can be washed very easily (inside and out) with water and a soapy solution. They also dry quickly. The mid-calf design, pull loops, and slide-in grooves allow you to pull these boots on and off easily. The slip-resistant rubber lug sole reduces the risk of slipping on wet and muddy surfaces.

The main features of these ankle boots

We recommend that you choose your usual size. Indeed, there is no fabric inside the boot and therefore no additional thickness. A specific sole is available to promise for this model (see Sole 100), which provides even more comfort, especially in winter. In these conditions, you can step in puddles or walk in the rain while keeping your feet dry.

Further details

41/42: 1.32 kg
9.5/10.5: 1.46 kg
11.5/12: 1.68 kg

Size                       Inner height (mm)	
41/42	                260	
43/44	                270
45/46	                280

Size                       Inner height (mm)	

41/42	                    280	
43/44		            290	
45/46		            300

Exterior height (mm)

Size             Calf circumference (cm)

41/42		        40
43/44		       41.5
45/46		        43 

Calf circumference (cm)

Fitting comfort

Synthetic upper withstands saddle friction.

Durability

You can cut these boots using scissors if they are too high.

Easy to clean in fresh water - perfect if it rains.

Our horseback riding designers developed these versatile synthetic boots for beginner riders! 

Drying in a tumble dryer possible. Normal temperature, maximum exhaust air temperature of the drum 80°C.

Iron at a maximum soleplate temperature of 150°C.

Wash with clean water using a slightly damp sponge. If your boots get damp inside, stuff them with newspaper to absorb the moisture.

Care advice

Perfect for getting into the sport. Ideal for beginner riders. Very easy care.

How to use

Riding Boots & Half-Chaps

Tested in 2 hours of moderate rain
15,000 mm Schmerber

Very breathable coated fabric (RET < 12): less condensation.

3 zip pockets, including 1 inner pocket.

Exterior coating to help counter the wind chill.

Fabric treated so that water slides off the surface.

Water repellent

Resistance to salt water

An inshore jacket for sailing in warm and stormy weather.

Ventilation Zippers

Collar Type

sleeve length

Hood

Style

We measure a fabric’s resistance to water pressure in mm of water column (based on the ISO 811 standard). The higher the water pressure a fabric can withstand, the more waterproof it is.
Waterproofing ratings:
Component resistant to water pressure of 15,000 mm before and after ageing (5 washes). This is equal to 15,000 Schmerber (the average pressure exerted during rainfall).
This jacket was tested in 2 hours of moderate rain (60 L/m²/h).

Waterproofing 1/2

- High collar
- Injection-moulded plastic to avoid salt oxidation
- Water-repellent components (water runs off the fabric)
- 100% taped seams
- Central opening features a flap with a drainage channel for optimal waterproofing

Waterproofing 2/2

The hood is attached and doesn’t stow into the collar.
Height- and depth-adjustable.
The hood visor and headband provide good coverage and a better hold.
The high collar protects your neck.

Features 2 front zip pockets and 1 inner right chest pocket with a rip-tab closure. Note: Pockets are not waterproof.

The full-length zipper includes an inner storm flap that protects you from wind and water,
and the collar has a soft flap to shield your chin.

Front zipper

To find out if a fabric is breathable, we measure its resistance to evaporative heat transfer (RET). The lower the RET, the easier it is for water vapour generated during physical exertion to pass through the fabric.
For example:
RET < 9 = very breathable;
RET 9–12 = breathable.
 
     

This jacket stays lightweight and breathable in wet conditions because water
slides off the treated fabric instead of seeping in. The water-repellent coating applied to the jacket’s exterior may change over time.
To restore it, place the jacket in the dryer for 10 minutes at the lowest temperature.

Water repellency

To preserve its water-repellent coating, do not wash this jacket too often.
Close all zippers and flaps, empty all pockets, and turn the jacket inside out. Wash it on the synthetics cycle at 30°C or 40°C with your usual detergent. Don’t use fabric conditioner or bleach, as these could damage the water-repellent coating. Very important: Choose a full-rinse cycle or extra rinse.

How to wash your jacket

Drying is a crucial phase in restoring the water-repellent treatment.
We recommend laying your garment flat on a clothes rack to dry. Warning: Never dry your jacket directly on a radiator.
Next, put your garment in the dryer and run a short synthetics cycle (10–15 min.) before turning it right-side-out. Caution: Do not over-dry the garment.

How to restore water repellency

Flexible, grooved sole for good water drainage.

Grip

Removable insole for better insulation and cushioning.

These comfy boots were designed for occasional inshore sailing.

Maximum wash temperature 95°C. Normal cycle.

Removable Sole

Sock Height

Designed with a neck (top of boot) so kids can easily slip in and out of them.

Size in 9C/10C: 20 cm. 20 cm

Features

The environmental impact of the product is calculated over its entire life cycle with different indicators. A score (ABCDE) easily identifies the products with the best environmental performance by comparing products of the same type.  Decathlon applies this scheme voluntarily. Learn more at sustainability.decathlon.ca

A score to compare products’ environmental impact

Rain boots

clearance

Very light at just barely 1.21 kg in size 8/9.

Lining-free technology: inside and out washing, quick drying.

These ankle boots are waterproof and very light. comfortable when walking, and dirt is easy to clean off.

Boots for women in nature

The PVC boots we offer here can be washed easily (inside and out) with water and a soapy solution. They also dry quickly. The mid-calf design, pull loops, and slide-in grooves allow you to pull these boots on and off easily. The slip-resistant rubber lug sole reduces the risk of slipping on wet and muddy surfaces.

We recommend that you choose your usual size. Indeed, no fabric inside the boot and therefore no additional thickness. A specific sole is available for this model (see Sole 100), which provides even more comfort, especially in winter. In these conditions, you can step into water puddles or walk in the rain and still feet dry.

3.5/4: 980 g
5/6: 1.04 kg
8/9: 1.21 kg
9.5/8: 1.32 kg

Size             Inner height (mm)	

35/36	                   230	
37/38	                  240
39/40	                  250
41/42	                  260

Size  Exterior height (mm) 

35/36		250	
37/38		260	
39/40		270	
41/42	        280

Size        Calf circumference (cm) 

35/36	              36
37/38	              37
39/40	         	39
41/42		        40

Tested in moderate rain for 2 hours
5,000 mm Schmerber
Pockets are not waterproof.

Compact enough to pack into one of its pockets.

This jacket is designed for sailing in warm, stormy weather.

We measure the resistance of a fabric to water pressure in mm of water column (based on the JIS standard).The higher the water pressure a fabric can withstand, the more waterproof it is.
On our Sailing 100 jacket.
Component resistant to water pressure of 5,000 mm Schmerber (JIS standard) before and after ageing (five washes).  This equates to the average pressure applied by the water during a rain shower. 
This jacket has been tested in 2 hours of heavy rain (60 L/m²/h).

To find out if a fabric is breathable, we measure its resistance to evaporative heat transfer (RET). The lower the RET, the easier it is for water vapour generated during physical exertion to pass through the fabric.
For example:
RET < 9 = very breathable;
RET 9–12 = breathable.
The RET of this sailing jacket is 12.

Supple material for good flex.Removable sole.

Fully injected sole and upper to avoid any risk of them coming apart.

Shaft high enough to provide good ankle support.

The elasticated gusset and tongue guide the foot into the boot.

Easily cleaned with water. The sole can be removed to speed up drying.

The sole offers a good grip on the stirrup iron. Heel stops foot getting stuck.

Our equestrian designers created these jodhpur boots for occasional riders. They're easy to put on and can be worn in all weather.

These jodhpur boots go perfectly with the Mesh Half-Chaps 100.

Style:

Ideal for wet and muddy ground, they're waterproof and easily washable.

Conditions for use: 

Remove any sand or dirt using a soft brush, then clean with a damp cloth. No product necessary: plain water gets the job done!
If drying in a damp area, simply remove the insole to dry it and, if needed, insert newspaper in the jodhpur boots to absorb moisture.
Do not dry near a heat source (heater, fire).

Care advice: 

Comfort temperature when stationary: -9°C.
When active: -18°C.

Warmth

100% waterproof monoblock clog (the upper has no waterproof membrane).

Tread with Snow Contact technology: sole materials and tread pattern for snow.

The position and depth of the 5-mm studs provide traction on snow.

Wide boot opening makes them easy to put on and guarantees support.

Would you like to explore snow-covered trails? These boots are ideal for occasional hikes in shallow or packed snow.

Outsole Technology

comfort temperature

Foot Width

A warm, insulated lining effectively protects you from the cold.

Lab- and field-tested with hikers. We verified the comfort temperature both at rest and when walking, as this can vary significantly: -9°C when static and -18°C when moving. We also considered how men and women feel the chill differently.

Are my boots warm enough for my winter hikes?

A 100% waterproof mid-height inner shoe protects the part of the foot most in contact with the snow. The textile upper is water-repellent and warm for good protection against cold and snow.

How do my boots protect me from outdoor conditions?

A boot’s traction depends on the number and shape of the studs. The grip depends on the sole materials and the tread pattern, like car tires. Traction optimizes propulsion, prevents slipping when going uphill, and stabilizes the boot. 
Grip prevents the boot from slipping and skidding on smooth ground or in demanding conditions (rain, snow, and ice).

What is the difference between traction and grip?

Boots with Snow Contact soles provide maximum grip and traction on snow for hiking. The strategic arrangement and height of the lugs (5 mm) ensure optimal grip when hiking on snow. The lugs are designed to grip hard snow and evacuate excess water to avoid slipping.

Which type of grip and traction does this boot provide?

The material and tread of Snow Contact soles are specifically designed for optimal grip and traction. Snow Contact soles are more effective on snow than traditional soles. When walking on ice, adding anti-slip grips to your boots is the only way to ensure optimum safety.

What are the advantages of Snow Contact technology?

This product was lab-tested by our engineers to ensure your total satisfaction. We tested the following elements: tear resistance of eyelets and straps, bonding, toxicology, UV resistance, abrasion resistance of outsole and upper components, and accelerated aging.

Will my boots withstand regular use over the long term?

Follow these guidelines for winter activities: Warmth: Wear warm socks (ideally with a good percentage of wool).
Breathability: Choose socks based on the intensity of the hike and make sure they’re breathable, to minimize moisture.
Boot height: The height of the sock should correspond to the height of the boot—for more protection, choose higher socks.

The right footwear for hiking in snow

Water repellency is a fabric’s capacity to make water run off its surface without being absorbed. It prevents the fabric from soaking up water, keeping it lightweight, warm, and breathable. Water repellency is achieved by treating the fabric’s exterior. This treatment needs to be reapplied throughout the product’s lifetime. Products for this purpose (spray or liquid) are available in our stores.

How to preserve the technical qualities of my boots

This product is guaranteed for two years from the date shown on the sales receipt. A product covered by the warranty will be exchanged free of charge. The warranty covers product defects, excluding those resulting from normal wear and tear or improper use.

How does my product warranty work?

An ABCDE rating shows the environmental impact of a product. Put forward by ADEME, it takes into account production, transportation, usage, and waste generated at the end of a product’s life. Decathlon displays this information voluntarily to help you identify products with lower environmental impact. Learn more at sustainability.decathlon.com

Our products’ environmental impact

Winter Boots

These waterproof boots will keep feet dry on board and on shore in wet weather.

Sports/

Water sports/

Sailing/

Rain boots/

tribord

Waterproof Sailing Boots - 100 Blue