100% effective on all types of Butyl inner tubes.

Compatibility

Less restrictive and just as effective as a classic patch.

Ease of use

Easy assembly/dismantling

This self-adhesive patch kit lets you easily and quickly repair punctures so you can carry on enjoying your bike rides.

Tire Assembly

Condition

Skill Level

Assembly Type

1. Remove the inner tube and locate the puncture
2. Roughen the area around the puncture using the sandpaper
3. Clean and dry this area
4. Apply the self-adhesive patch and press hard on the entire area for around 45 seconds
5. Run your nail over the patch to increase its adhesive power
6. Put the inner tube back in the tire and the tire in the rim
7. Inflate your tire to the recommended pressure.

User tip: 

Optimal lifespan: 3 years at room temperature (16-22°C, 30-70% humidity), away from direct light and in its original packaging.
Minimum temperature for repairs: +10°C 
Temperature for use: -40°C to +65°C

Storage:

Be careful not to touch the sticky part when positioning the patch, so as not to reduce its sticking power.
Remove any air bubbles by pushing from the centre of the patch towards the edges.
Rub the patch with your nail to warm it up and help it stick better.
Finally, press firmly with your thumb, covering the entire patch for 45 seconds to 1 minute (press on a clean, flat surface for greater effectiveness).

Applying the patch: 

A good sanding of the area concerned will give you a better result.
The aim is to obtain a flat, clean surface so the patch holds as well as possible.If the puncture is close to excess material, sand until the excess is removed.
Sanding will create micro-scratches that will allow the glue on your patch to set more easily.
This stage is very important for a lasting repair.

Sanding: 

Clean away any impurities to ensure a clean, flat, and dry area to apply the patch.
Remember: don't use water or any other product to clean your inner tube after sanding. It's essential to have a clean, dry surface to ensure that your patch lasts.

Cleaning: 

Rockrider

clearance

with 700 diameter tires, 23 to 32 mm cross-section. ETRTO 23/32 – 622

Optimized composition to guarantee your inner tube has a good seal.

Waterproof

Designed for replacing the inner tube of your 700 diameter, 23 to 32 section tires with a 48 mm (2") Presta valve.

Valve Type

Frequency

Wheel Size

Self-Repair

Section

Etrto

Check all the information indicated on the sidewall of the tire (diameter and width). For example, 27.5 x 1.90 means a tire with a 27.5" diameter that is 1.90" wide.
The dimensions in mm are also on the tire sidewall.
For example, 50-584 means your tire is 50 mm wide with an inner diameter of 584 mm (approx. 27.5 x 2.00).

How to choose your inner tube

Remove the old inner tube using a tire lever.

Removing an inner tube

Check the condition of your tire and replace it if necessary. 
Make sure no objects are lodged in the tire.
Check the condition and position of your rim strip.
A rim strip that’s even slightly bent can cause punctures.
Check that your rim doesn’t have any other issues that could damage your inner tube.

Checks to carry out before installing an inner tube

Watch our video before you start.
Pre-inflate the inner tube slightly to avoid pinching.
Make sure you’re using the correct valve for your rim and then insert it.
Put the entire inner tube inside the tire so that it fits inside the rim.
Take care not to pinch the inner tube when installing it.

Installing the inner tube

Start installing the tire at the valve.
Finish installing the tire across from the valve to avoid pinching the inner tube.
Never install your tire with a tool or a tire lever, as you risk pinching or puncturing the inner tube.

Installing the tire

Carefully inflate your tire to the pressure recommended by the manufacturer (visible on the tire sidewall in PSI or bars: 1 bar = 14.51 PSI).
Regularly check that your tire is in the correct position as you inflate it.

Inflating the tire

To avoid punctures from pinching and for the best tire performance, we recommend checking your tires and inflating them to the suggested pressure before every ride.

Our professional advice

Weight:

Bike Tubes & Valves

onlyonline

Shelf for your tools and 360° rotating clamp.

Can be folded (central tube). 
Dimensions when folded: 120 x 12 x 9 cm.

Compact design

Adjust the stand height for comfortable use, from 1.10 m to 1.52 m.

Adjustable

Stable enough to hold bikes weighing up to 25 kg/55 lb thanks to the three legs.

Stability

This bike repair stand was designed to allow you to take care of your bike indoors or outdoors on a stable stand.

Intensity

Maximum Bike Weight

Maximum Load

Attachment

Number of Bicycles

Main Material

For greater comfort during maintenance, clamp the bike so that the rear wheel is higher than the front wheel. This will keep the handlebars level.

Our advice for positioning your bike

You can use this repair stand with bikes weighing up to 25 kg/55 lb and frame tubes with a maximum diameter of 5 cm.

What kind of bike is it for?

During assembly, remember to position one of the three feet in line with the arm to ensure the best possible stability.

Assembling your repair stand

Packaging dimensions:  108.5 x 20 x 12 cm (42,7″ x 7,9″ x 4,7″)

Stand height adjustment: 1.10 m to 1.52 m (43,3″ à 59,8″)

Features

Bike Tools

12 lumens in white (continuous, flashing).
4 lm. in red (continuous, flashing).

Visibility

Cont. white 30h / flash. 50h
Cont. red 30h / flash. 50h
Batteries (CR2032 incl.)

Autonomy

White and red, 2 modes (continuous and flashing).
Universal elastic mount.

Versatility

This front or rear bike light is designed to keep you visible. Easy to use with its 2 modes, 2 colours, and elastic fastening system.

Weight (g)

Brightness (Lumens)

reflective

Lighting Type

Type Light

Sold In Set

Position

Autonomy (H)

Hook Type

Power Type

Range (m)

Feedback from cyclists and other road users (drivers, pedestrians, etc.,) led to optimum features for cyclists’ visibility. 

With one purpose in mind: the cyclists’ safety.


Lights

Home trainer tire designed to resist against roller wear.

Abrasion resistance

Traction

Developped for home trainer use, the B'Twin Home Trainer tire will improve performance during your sessions.

tire width x wheel size

Tire Bead

Type of Tyre

tire compound type

e-bike ready

Width (mm)

Bike Tires

Lets you make basic repairs and adjustments to your bike.

4 Allen keys (3/4/5/6 mm), 1 Phillips & 1 flat screwdriver.

Weight

Tool size indicator on the ends for getting the right tool quickly.

This multitool was designed to let you make adjustments and/or repairs to your bike while out on a ride.

Number of Functions

4 Allen keys (3/4/5/6 mm)
1 Phillips screwdriver
1 flathead screwdriver.

Includes

Spare Parts

27.5" tires with 1.90 to 2.50 cross-section.

ETRTO 47/64 – 584

This inner tube is suitable for 27.5" diameter tires with 1.90 to 2.50 cross-section with a 48 mm Schrader valve.

Check the information indicated on the sidewall of the tire (diameter and width). For example, 27.5 x 2.20 means that the tire is 27.5" in diameter and 2.20" wide.
The dimensions in mm (ETRTO international unit) are also on the tire sidewall. For example, 50-584 means that the tire is 50-mm wide with a 584-mm inner diameter (approx. 27.5 x 2.00).

Remove the old inner tube using Btwin tire levers.

Check the condition of your tire and replace it if necessary. 
Make sure no objects are lodged in the tire.
Check the condition of your tire rim strip. A rim strip that’s even slightly bent can cause punctures.
Check that your rim doesn’t have any other issues that could damage your inner tube.

Pro tip

This degreasing brush allows for an efficient application of your degreaser.

This brush is ideal for applying your plant-based degreaser to your bike's drive train (chain, derailleurs, cassette, etc.). 

Application Type

Volume (ml)

Type of Brush

To ensure optimal maintenance, we recommend that you follow these three steps: 
1) Degrease your drive train
2) Clean your bike
3) Lubricate your chain

With this bike degreasing brush, you can apply your plant-based degreaser to your drive train and complete Step 1.

How to maintain your bike

This brush comes with a protective cap, allowing you to place it easily on a workbench or shelf, protect the bristles from being crushed, and keep your toolbox clean.
Do not pour degreaser directly into the brush, as it may overflow when inserting the brush, leading to unnecessary waste.

Features: 

Long-lasting rust protection in all weather conditions.

Corrosion resistance

Smooth pedalling

Lubricating the chain reduces disturbing noises.

Noise level

This lubricant is designed for lubricating your drive train during rides in all weather conditions.

Weather Conditions

Shake the bottle before use.
Only apply to the inside of the chain, i.e. the part in direct contact with the chainring teeth and the derailleur jockey wheels. 
Wipe off any excess with a microfibre cloth.

Advice from our team: 

To ensure optimal maintenance, we recommend that you follow these 3 steps: 
1. degrease your drive train
2. clean your bike
3. lubricate your chain

How to look after your bike:

This all-weather chain lube is designed for doing step 3. Once you've applied the degreaser (step 1), spray the bike with the cleaner and rinse and dry it (step 2), then apply your bike lube (step 3). Your bike will be as good as new.

How to use this product: 

Remember to degrease your chain before greasing it in order to remove any residue that could make abrasive contact with your drivetrain. This will help your equipment last longer and save you money.

Maintenance advice: 

100 mL (3 1/2 oz.) bottle = approx. 40 uses

Made in:

Capacity:

Replaces the chain of your 3- to 8-speed bike. Compatible with 3- to 8-speed Shimano, Campagnolo and SRAM derailleurs

Number of Speeds

Number of Links

For easy assembly, adapt chain length with a chain tool available on our website (ref: 8351521)

Mounting

For easy dismanteling, use a quick link chain tool and/or a chain tool available on our website (ref: 8352339 and 8351521)

Dismantling

Number of links

Bike Chains

Limits taste and odour

100% waterproof with the mouthpiece closed, non-drip with mouthpiece open.

Ergonomic shape and soft material make it easy to drink as you ride.

Ergonomic grip

Comfortable mouthpiece made of soft elastomer.

Mouth comfort

Capacity

Clear body graduated for easier intake monitoring.

Precision

The elastomer cap won’t slip off and makes closing the bottle easy.

Compatible with all bottle cages on the market.

Developed for demanding cyclists who want a bottle that keeps them hydrated as they ride.

isothermal

Cap Type

All of our "FastFlow" bottles use the SureSnap® valve, the best on the market. This valve controls the flow of water effectively and precisely. When you press down, water squirts out of the mouthpiece.
Plus, the anti-leak mouthpiece can stay open while riding without water dripping onto your bike's frame.

SureSnap® valve

The mouthpiece is 100% watertight in closed position. Use this position for mixing the isotonic drink in the bottle or for carrying it in a bag.
Once on your bike, leave it open. The SureSnap® valve prevent leaks. Drink quickly and safely!

How to use the FastFlow valve

There’s nothing worse than a plasticky taste or smell in a water bottle. But this is the case for most cycling water bottles. 
We tested numerous plastics before finding just the right one, which is supple and has a neutral taste and smell. When blind tested against bottles from other leading brands, ours were the most neutral-tasting.

No more plasticky smell or taste.

Clean the water bottle thoroughly after each use. If you use isotonic drinks, rinse all parts of the bottle, cap, and mouthpiece to make sure there is no liquid remaining inside. Use liquid detergent and a long brush to clean the bottom of the bottle. 
Dry well and store with the cap off. Otherwise, mould could develop in the bottle.
Do not put in the dishwasher (particularly above 70°C).

How to care for your water bottle

Bike Hydration

Stretchy enough to fit different head sizes.

Anatomic design

A lightweight product that's easy to wear in hot weather.

Lightweight

The perfect protection for cycling in warm weather.

Maximum washing temperature 30°C. Normal cycle.

Type of Beanie

Style

Bike Helmets

700 diameter tires, 23-32 mm cross-section
80-mm Presta valve
ETRTO 23/32 – 622

Compatible with 700 diameter tires, with a cross-section ranging from 23 to 32 and an 80-mm Presta valve.

Check the sidewall for tire information (diameter and width). For example, 27.5 x 1.90 means a tire with a 27.5” diameter that is 1.90” wide.
The dimensions in mm (ETRTO international unit) are also on the tire sidewall.
For example, 50-584 means your tire is 50-mm wide with an inner diameter of 584 mm (27.5 x 2.00).

Check the condition of your tire and replace it if necessary. 
Make sure no objects are lodged in the tire.
Check the condition of your tire rim strip.
A rim strip that’s even slightly bent can cause punctures.
Check that your rim doesn’t have any other issues that could damage your inner tube.

Compatible with bikes equipped with bottle cage screws.

Designed for carrying a water bottle on your bike.

The 3 products are suitable for every kind of bike, mechanical, or electric.

Get your drive train and your bike in perfect shape.

Visual efficiency

With its compact size, you can take the kit everywhere with you.

This bike cleaning kit follows just 3 steps: degrease, clean and lubricate. Care for your electric, road, city, mountain, hybrid bike and more.

Maintaining your bike will let you:
- Extend the life of the various components 
- Ensure that it works properly
- Reduce unwanted noise
- Prevent breakages
- Enjoy the pleasure of riding a clean bike

Why should you maintain your bike?

To ensure full maintenance, we recommend that you follow these 3 steps: 
01. degrease your drive train
02. clean your bike
03. lubricate your chain

Sports/

Cycling/

Bike Tools and Components/

Bike Tools/

decathlon

Bike Tire Lever