Flexible Snowboard Boots – SNB 100

Name: Flexible Snowboard Boots – SNB 100
Availability: InStock

Their flexibility is forgiving of learning errors, and the inner and outer lacing system allows you to tighten the boots as suits you best. The liner is thermoformable.

ID 8872187

Sold and shipped by

How to get it

Fit
10 mm foam heel support: comfort and support at moderate speeds.
Easy opening/closing
Easy, durable tightening; classic laces.
Flexibility
Flex (3/10) is forgiving of mistakes and improves comfort.
Thermal insulation
EVA foam sole: 80% air insulates from cold ground.
Fitting comfort
Easy to get on. Flexible foam: maximum comfort. Thermoformable liner.
Traction
Ultralight outsole with large studs for good grip on all types of snow.
Cushioning
Ultralight cushioning EVA sole (80% air).

Description

Design details

Quick tightening system
Laces and a blocker that is easy to use for fast tightening. The outer tightening system uses classic laces.
Boot flex/stiffness
Adequate flex is something we strive for. It improves comfort, reduces physical fatigue, and allows you to fully enjoy your day in the snow. It helps beginners adopt the right position on the board: ankles flexed to avoid straight legs. Snowboarding demands fast reactions, and keeping knees bent is important. You don’t want to start with a boot that’s too stiff.
Adding Flex Up
The Flex Up enables you to add 2 out of 10 flexion points (with Flex Up, this boot has a rigidity of approximately 5/10). This is a plastic accessory which is inserted into the tongue of Decathlon snowboard boots produced from the 2022/23 season onwards. A pocket has been included in the design to keep it in the ideal position. The Flex Up adds stiffness: If your boot turns more limp, give it a second life.
Heel support: level 1 liner (/3)
Foot support is essential for steering your board. The level 1 liner has 4 features: 1. Liner that can be thermoformed at home 2. Comfort Heel Pad ankle foam 3. 4-point liner tightening 4. Hook-and-loop tab on the top of the liner
1. Thermoforming the liner by yourself: Warning
Thermoforming is only possible in built-in ovens measuring 56 cm x 60 cm x 56 cm (22” x 23.5” x 22”) equipped with a fan mode. Do not attempt in a gas oven or small toaster oven with visible heating elements.
1. How to thermoform the liner yourself
1. Heat your oven to 80°C in convection mode. 2. Remove the inner soles from the liners. Place the liners on a baking sheet covered with a piece of parchment paper. 3. Wait 15 minutes. 4. Put them on with a pair of ski or snowboard socks and tighten them (not too much). 5. Put on the boots on and tighten fully. 5. Wait for 15 minutes. This operation can be repeated if necessary. For use in a built-in oven (56 cm x 60 cm x 56 cm/22” x 23.5” x 22”) only
2. Comfort Heel Pad ankle foam
Ankle padding fills the hollow under and behind the ankle, keeping the heel firmly in place. The level 1 liner is made of a relatively soft, one-piece material with 10 mm (0.39”) thick foam ankle pads. The goal is to provide heel-foot support that matches the boot’s performance level. In fact, the faster you go, the more energy is deployed and the more support your foot needs. Comfort Foam provides maximum comfort.
3. 4-point liner tightening
4-point tightening for good foot support. It holds the foot in place around the ankle.
4. Hook-and-loop strip on top of liner
The top of the liner has hook-and-loop strips, enabling you to hold the tongue of the liner in place at the sides, no matter how your foot is moving.
Insole
The insole of this boot is flat. It offers comfort and thermal insulation. If you really need added support for your foot, here’s what you can do: - add a sole that is pre-formed at the arch and heel area - add a sole that can be thermoformed to your foot This is the most effective solution.
Sole: grip, traction, cushioning, and thermal insulation
Our Ultralight sole is 100% EVA. EVA is a very light material with 80% air. This material resists abrasion while maintaining its damping properties. It is naturally very insulating and protects you from the cold ground. The lug tread offers excellent grip without retaining snow.
How to choose the right size
1. Put the boot on. 2. Tighten the boot. 3. Stand up. 4. Your big toes should touch the tip of the boot without excessive pressure. 5. Bend your legs forward; your big toes should move back, no longer touching the front of the boot.

Raw material	88%
Manufacturing	2%
Packaging	0%
Distribution	5%
Use	1%
End of life	4%

Raw material	88%
Manufacturing	2%
Packaging	0%
Distribution	5%
Use	1%
End of life	4%

Flexible Snowboard Boots – SNB 100

How to get it

Features

Fit

Easy opening/closing

Flexibility

Thermal insulation

Fitting comfort

Traction

Cushioning

Description

Design details

Specifications

Details

Composition

Legal notice

EU product safety contact

Usage & care

Environmental impact

Carbon footprint

Description

Design details

Specifications

Details

Composition

Legal notice

EU product safety contact

Specifications

Details

Composition

Legal notice

EU product safety contact

Usage & care

How to use

How to repair or replace

2-year warranty

Care instructions

Storage

Cleaning

Environmental impact

Carbon footprint

Specifications

Details

Composition

Legal notice

EU product safety contact

How to use

How to repair or replace

2-year warranty

Care instructions

Storage

Cleaning