10 mm foam heel support: comfort and support at moderate speeds.

Easy opening/closing

Flex (3/10) is forgiving of mistakes and improves comfort.

Flexibility

EVA foam sole: 80% air insulates from cold ground.

Thermal insulation

Easy to get on. Flexible foam: maximum comfort. Thermoformable liner.

Fitting comfort

Ultralight outsole with large studs for good grip on all types of snow.

Traction

Ultralight cushioning EVA sole (80% air).

Cushioning

Very comfortable, these boots make learning easier and help you progress.

Condition

Skill Level

heat moldable liner

tightening zone

Flex

Type of Liner

Tightening Type

Laces and a blocker that is easy to use for fast tightening. The outer tightening system uses classic laces.

Quick tightening system

Adequate flex is something we strive for. It improves comfort, reduces physical fatigue, and allows you to fully enjoy your day in the snow. It helps beginners adopt the right position on the board: ankles flexed to avoid straight legs. Snowboarding demands fast reactions, and keeping knees bent is important. You don’t want to start with a boot that’s too stiff.

Boot flex/stiffness

The Flex Up enables you to add 2 out of 10 flexion points (with Flex Up, this boot has a rigidity of approximately 5/10).
This is a plastic accessory which is inserted into the tongue of Decathlon snowboard boots produced from the 2022/23 season onwards. A pocket has been included in the design to keep it in the ideal position.
The Flex Up adds stiffness: If your boot turns more limp, give it a second life.

Adding Flex Up

Foot support is essential for steering your board. The level 1 liner has 4 features:
1. Liner that can be thermoformed at home 
2. Comfort Heel Pad ankle foam 
3. 4-point liner tightening
4. Hook-and-loop tab on the top of the liner

Heel support: level 1 liner (/3)

Thermoforming is only possible in built-in ovens measuring 56 cm x 60 cm x 56 cm (22” x 23.5” x 22”) equipped with a fan mode. Do not attempt in a gas oven or small toaster oven with visible heating elements.

1. Thermoforming the liner by yourself: Warning

1. Heat your oven to 80°C in convection mode. 
2. Remove the inner soles from the liners. Place the liners on a baking sheet covered with a piece of parchment paper.
3. Wait 15 minutes.
4. Put them on with a pair of ski or snowboard socks and tighten them (not too much).
5. Put on the boots on and tighten fully. 5. Wait for 15 minutes. 
This operation can be repeated if necessary.
For use in a built-in oven (56 cm x 60 cm x 56 cm/22” x 23.5” x 22”) only

1. How to thermoform the liner yourself

Ankle padding fills the hollow under and behind the ankle, keeping the heel firmly in place.
The level 1 liner is made of a relatively soft, one-piece material with 10 mm (0.39”) thick foam ankle pads.
The goal is to provide heel-foot support that matches the boot’s performance level. In fact, the faster you go, the more energy is deployed and the more support your foot needs.
Comfort Foam provides maximum comfort.

2. Comfort Heel Pad ankle foam

4-point tightening for good foot support. It holds the foot in place around the ankle.

3. 4-point liner tightening

The top of the liner has hook-and-loop strips, enabling you to hold the tongue of the liner in place at the sides, no matter how your foot is moving. 

4. Hook-and-loop strip on top of liner

The insole of this boot is flat. It offers comfort and thermal insulation. 
If you really need added support for your foot, here’s what you can do: 
- add a sole that is pre-formed at the arch and heel area
- add a sole that can be thermoformed to your foot This is the most effective solution.

Insole

Our Ultralight sole is 100% EVA.
EVA is a very light material with 80% air. This material resists abrasion while maintaining its damping properties. It is naturally very insulating and protects you from the cold ground.
The lug tread offers excellent grip without retaining snow.

Sole: grip, traction, cushioning, and thermal insulation

1. Put the boot on. 
2. Tighten the boot. 
3. Stand up.
4. Your big toes should touch the tip of the boot without excessive pressure.
5. Bend your legs forward; your big toes should move back, no longer touching the front of the boot.

How to choose the right size

Men's Snowboard boots

Good: bodymapping for effective moisture transfer and fast drying.

Moisture management

Average: bodymapping integrated into a brushed component (165 g/m²).

Warmth

Seamless technology: fewer seams to reduce irritation.

Reduced chafing

The component limits sweat odours. 
Lab tested to ISO 17299-3 standard.

Odour control

Hit the slopes without worrying about the cold and damp! A breathable base layer that prevents the sauna effect while you’re out doing moderate exercise. 

Maximum washing temperature 30°C. Normal cycle.

Intensity

Frequency

Collar Type

Weather Conditions

sleeve length

Place of Practice

Waterproof

anti-uv

Pocket

Style

Main Material

The BL 500 soft thermal base layer comes in a slim fit. This slim-fitting base layer reduces friction.

Polyamide is the strongest of all raw textile materials, even when wet, and it is very stretchy.
This breathable fibre manages moisture very well and provides good temperature regulation.
These specially textured, super-soft yarns give the fabric a silky, natural feel. Ideal for tight, seamless clothing.

What are the benefits of polyamide?

Thanks to its bodymapping technology and brushed polyamide fibre created with I-Soft technology, this second skin will evenly distribute body heat.

Technical product structure

The I-Soft technology enhances the fabric’s performance, providing a variety of benefits: softness, warmth, and comfort. It also enhances garment performance, providing better heat regulation, humidity absorption, and thermal insulation. To achieve this softness, the base layer is brushed.

What is I-Soft technology?

The I-Band technology is an innovative design used around the waist of the I-Soft top and bottom base layers. It helps keep the garment in place so that it doesn’t ride up or fall down when skiing.

What is I-Band technology?

You need three technical layers to keep warm on the slopes:
- Layer 1 or a second skin, to stay dry. 
- Layer 2 or an insulating layer, to keep the heat in.
- Layer 3 or a protective layer to protect against the elements.

How to dress to stay warm on the slopes

We commit to repairing your product free of charge for the duration of the warranty. If you need seams, zippers, or another element repaired, contact your store. 
However, if we can’t repair your product (production defect), we will exchange it or reimburse you.

This product is repairable

The model wears size M and is 175 cm (5’9”) tall.
Measurements:
Waist size: 67 cm (26.4 in)
Hip measurement: 99 cm (39 in)
Chest size: 90 cm (35.4 in)

To help you choose the right size

Ski Base Layers

clearance

Complies with EN1077:2007 standard (class B). Lightweight In-Mold structure.

Impact protection

Head size adjustment dial, full coverage.

Stability

6 holes and ventilation channels for breathability and moisture management.

Ventilation

410 g in size M. The lightest helmet in the range.

Lightweight

Ear pads and thick hat in a brushed material.

Ease of use

Warm, well-ventilated liner with full coverage.

User comfort

Developed for regular skiers looking for a light, comfortable, ventilated helmet that they’ll forget they’re wearing. 

Adjustable Helmet

Ventilation Zippers

Weight (g)

Season

helmet compatible with

protection technology

material of the exterior shell

type of chin guard

helmet shape

reflective

removable foams

number of aeration points

Bluetooth Connection

RECCO system

Detachable Visor

Fastener Type

Wedze/Quechua helmets and goggles are designed to form an complete unit and prevent gaps between the top of the helmet and the goggles.

Compatibility

Use the adjustment dial to secure your helmet. The dial can be easily adjusted while wearing gloves. It also provides comfort and maximum safety. Turn the dial to the right to tighten and to the left to loosen.

Tightening dial

This type of structure, known as In-Mould, features a polycarbonate outer shell that is moulded directly to the EPS liner. The inner EPS liner absorbs shocks in the event of a collision. The whole thing is extremely lightweight. The In-Mould construction is more sensitive to everyday impacts. We recommend changing your ski helmet at least every five years or if it has sustained a significant impact.

In-Mold construction

Measure the circumference of your head (from the middle of your forehead to the top of your ears) and choose the right size. When trying on the helmet, you should not feel any discomfort. If the helmet does not have a visor, try it on with a pair of goggles: There should be no gaps between the two.

How to choose the right size and trying on your helmet

For your safety, your ski helmet must be properly adjusted:
- The head circumference must be adjusted using the tightening dial.
- The chin strap must be correctly adjusted. You should be able to fit two fingers between the strap and your skin. If it is not adjusted properly, the helmet will not protect you as it should.

Adjust your helmet once you have the right size

We recommend replacing your ski helmet at least every five years unless it has sustained a significant impact in the meantime. In the event of a strong impact, the helmet must be replaced: even if it is not visible, the internal material may be damaged and your helmet will provide less protection.

When should you replace your ski helmet?

Avoid wearing a hat, as this will create a gap between your head and your helmet and reduce your protection. If necessary, opt for a very thin balaclava designed for this purpose. 
Avoid putting a camera on the helmet, as this will compromise your safety. The standard does not take into account any elements added to the helmet.

A helmet keeps you warm: it is not necessary, and even discouraged, to wear a hat underneath

Helmets used for head protection when downhill skiing and snowboarding are required to meet the European standard EN 1077:2007. This standard ensures that helmets absorb shocks and are resistant to penetration. There are two categories:
- Class A: protects the top and back of the head, as well as the ears and the side of the head.
- Class B: Protects the top and back of the head but does not cover the ears.

EN 1077 standard

Make sure this product is right for you before purchasing. If it is not suitable, you can return it under the following conditions: i.e. with the instructions, labels and, if applicable, the original packaging. it can be refurbished. 

Product returns (specific product: personal protective equipment).

Helmets

100% anti-UV, interchangeable brown and yellow lenses, S1 and S3, all-weather

Sun protection

High-performance anti-fog, double lens anti-fog treated and ventilated frame

Anti-fogging

Wraparound lens with high performance field of vision

Field of vision

Double-density foam and comfortable fabric

40 mm wide elastic with double non-slip silicone strap

2 buckles to adjust the length of the elastic

Adjustable

Size L with glasses, 145 mm width maximum

Interchangeable lens solution so that you no longer have to choose based on the weather! Compatible with prescription glasses. 

Strap Type

Technical Lens

Compatible with prescription glasses

Field of Vision

Minimizes Fogging

glass composition

strapping

fogging treatment

Glass Category

Case Type

With Case

Diving Mask Type

Because UV rays are harmful to eyes, all our ski goggles have 100% anti-UV certified lenses. Goggles are the best protective solution as they completely enclose the eyes, preventing any direct or reflected UV light from entering.

Ski goggles with interchangeable lens for all-weather use. 
S1 Fog is a light lens for seeing better in bad weather by improving landscape visibility.
S3 Sun is a dark lens that protects you from bright sunlight. To switch from fine weather to bad weather, just remove the fine weather lens (magnet). 
The screens are not scratch resistant.

S1 Fog and S3 Sun Lens with interchangeable lens function

The Performance anti-fogging system offers a dual lens with a treatment on the inside combined with a ventilation system on the frame that enables air to circulate inside the ski goggles.
For good ventilation inside your goggles, do not obstruct the air vents, with a neck warmer, for example.
Do not rub the inner surface of the lens. Dab it carefully in order to preserve the anti-fogging treatment for as long as possible.

High-performance anti-fogging performance

The dual screen reduces condensation. The air trapped between the lenses creates a layer of thermal insulation. The thermal shock between the inside and outside of the goggles is lower and so the inner lens does not fog up as quickly. To complement this, the inner lens is also given an anti-fog treatment.

Double lens

Triple cylindrical screen. The central lens is made from photochromic polycarbonate, making it resistant to impact. The inner lens is made from acetate and the interchangeable lens is flexible polycarbonate.

Wraparound lens

There is a vertical and a horizontal visual field. The G 500 have a high-performance field of vision, which offers good peripheral vision.

High-performance field of vision

All Wedze ski goggles are designed to fit perfectly with Wedze ski helmets.

Ski helmet compatibility

The G 500 I ski goggles, in size L, allow the use of max. 145 mm wide corrective glasses. The foam on the sides and the shape of the goggle skirt leave room for each temple. 

Compatibility with prescription glasses

40 mm wide polyamide, polyester and rubber elastic, 2 non-slip silicone straps

Strap

Protect the goggles, and the lens in particular, from scratches before and after use. 
This thermocompressed case is ideal for storing your goggles and protecting them from getting crushed in your bag or in a jacket pocket.

Thermocompressed case

A coloured coating on the outer side of the ski goggles lens (known as coloured Flash) reduces the percentage of light that reaches the eye, reducing glare and improving clarity in sunny conditions.
Warning: The lenses are not scratch resistant.

Coloured Flash lens

Moisture causes fogging. Keep the foam as dry as possible. For example, do not place the goggles on a wet helmet or a hat. Falling face down in the snow can also cause your goggles to fog up. Dry your ski goggles overnight to get rid of all traces of humidity and use completely dry goggles the next day.

Preventing condensation

Choose the right size goggles according to your head size. Below 55 cm, choose size S. Above 55 cm, choose size L.

Two sizes

Kids' Ski & Snowboard Goggles

Soft fleece balaclava for warmth and comfort.

Compact design

This fleece balaclava was designed to protect your child’s head from the cold.

Reversible

Breathability

Windproof

Type of Beanie

beanie compatible

Water-Repellent

Wearing a balaclava is also more hygienic if you rent or borrow a helmet.

Hygiene

Cut short in back to make it comfortable to wear with a ski jacket. This prevents added layers that can limit freedom of movement while skiing.

Cut of the balaclava

Wedze models fit children with a head size between 52 and 56 cm (20.5” and 22”). Depending on the elasticity of the weave, this measurement can vary slightly.

For a child with a head size between 48 and 52 cm (19” and 20.5”), choose the kid size. 
For a child with a head size below 48 cm (19”), choose a baby size.

Sizing

Kids' Neck Warmers

Component encourages wicking and minimal drying.

This ski base layer was developed for kids. It will keep them warm on the slopes.

dreamscape

Snowboard Bindings, SNB 500